CipherLab 1660 Specifikace Strana 90
- Strana / 156
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
78
Enter Setup
1660 Barcode Scanner
User Guide
4.12.3 CODE LENGTH QUALIFICATION
Because of the weak structure of the symbology, it is possible to make a "short scan"
error. To prevent the "short scan" error, define the "Length Qualification" settings to
ensure that the correct barcode is read by qualifying the allowable code length.
If "Max/Min Length" is selected, the maximum length and the minimum length must
be specified. It only accepts those barcodes with lengths that fall between max/min
lengths specified.
If “Fixed Length” is selected, up to 2 fixed lengths can be specified.
1) Read the label to enable either Max. /Min. Length qualification or Fixed Length(s)
qualification.
2) Read the label for Max. Length or Fixed Length 1, and follow steps 3~4.
Repeat steps 2~4 for Min. Length or Fixed Length 2.
3) Read the “
Decimal Value” label on page 141 for the desired length.
4) Read the “Validate” label on the same page to complete this setting.
E
nable Fixed Length(s) …
*Enable Max./Min.
Length (0 ~ 127) …
Min. Length (*4)
Or Fixed Length 2
Max. Length (*127)
Or Fixed Length 1
- IMPORTANT NOTICES 3
- RELEASE NOTES 5
- CONTENTS 7
- INTRODUCTION 13
- QUICK START 15
- ENTER CONFIGURATION MODE 16
- EXIT CONFIGURATION MODE 16
- Refer to Appendix III 20
- LIST THE CURRENT SETTINGS 21
- Chapter 1 23
- 1.1.3 AUTO POWER OFF 24
- 1.2 MEMORY 26
- 1.2.1 TRANSMIT BUFFER 26
- 1.2.2 MEMORY MODE 26
- Memory Data Delay 27
- Send Data 28
- Clear Data & Confirm 28
- 1.3.1 GOOD READ LED 30
- Beeping 31
- Meaning 31
- 1.4.1 BEEPER VOLUME 32
- 1.4.2 GOOD READ BEEP 33
- 1.4.3 LOW BATTERY ALARM 34
- 1.5 SEND “NR” TO HOST 35
- 1.6 SCAN MODES 36
- 1.6.1 CONTINUOUS MODE 37
- 1.6.5 AUTO POWER OFF MODE 39
- 1.6.6 AIMING MODE 39
- 1.8 DELAY BETWEEN RE-READ 41
- Continuous mode 41
- Auto Power Off mode 41
- 1.9 EFFECTIVE DECODING AREA 42
- 1.9.1 POSITIONING WINDOW 42
- 1.9.2 ADJUSTING WINDOW 42
- Percentage for Right Half 43
- 1.10 NEGATIVE BARCODES 44
- 1.11 SYMBOLOGIES SUPPORTED 44
- Chapter 2 47
- 2.1 BLUETOOTH HID 48
- 2.1.2 RESET CONNECTION 49
- Cap Lock Type Description 51
- Alphabets Transmission 52
- 2.1.4 INTER-FUNCTION DELAY 54
- 2.2 BLUETOOTH SPP 55
- 2.2.1 ACTIVATE BLUETOOTH SPP 55
- 2.2.2 INTER-FUNCTION DELAY 55
- 2.2.3 ACK/NAK TIMEOUT 56
- Chapter 3 57
- 3.1.3 AUTHENTICATION 59
- Chapter 4 67
- 4.1 CODABAR 68
- 4.1.3 CLSI CONVERSION 69
- 4.2 CODE 25 – INDUSTRIAL 25 70
- 4.2.2 CHECKSUM VERIFICATION 71
- 4.2.3 CHECKSUM TRANSMISSION 71
- 4.3 CODE 25 – INTERLEAVED 25 73
- 4.3.2 CHECKSUM VERIFICATION 74
- 4.3.3 CHECKSUM TRANSMISSION 74
- 4.4 CODE 25 – MATRIX 25 76
- 4.4.2 CHECKSUM VERIFICATION 77
- 4.4.3 CHECKSUM TRANSMISSION 77
- 4.5 CODE 39 79
- 4.5.2 CHECKSUM VERIFICATION 79
- 4.5.3 CHECKSUM TRANSMISSION 80
- 4.6 CODE 93 81
- 4.7 CODE 128 81
- 4.8 EAN-8 82
- 4.8.1 CONVERT TO EAN-13 83
- 4.8.2 CHECKSUM TRANSMISSION 83
- 4.9 EAN-13 84
- 4.9.1 ISBN CONVERSION 85
- 4.9.2 ISSN CONVERSION 85
- 4.9.3 CHECKSUM TRANSMISSION 85
- 4.10 EAN-128 86
- 4.10.1 CODE ID TRANSMISSION 86
- 4.11 ISBT 128 87
- 4.12 MSI 88
- 4.12.1 CHECKSUM VERIFICATION 88
- 4.12.2 CHECKSUM TRANSMISSION 89
- 4.13 FRENCH PHARMACODE 91
- 4.13.1 CHECKSUM TRANSMISSION 91
- 4.14 ITALIAN PHARMACODE 92
- 4.14.1 CHECKSUM TRANSMISSION 92
- 4.15 PLESSEY 93
- 4.15.1 CONVERT TO UK PLESSEY 93
- 4.15.2 CHECKSUM TRANSMISSION 93
- 4.16 RSS FAMILY 94
- 4.16.1 CODE ID SELECTION 94
- 4.16.2 RSS-14 94
- 4.16.3 RSS EXPANDED 95
- 4.16.4 RSS LIMITED 96
- Application ID Transmission 97
- Checksum Transmission 97
- 4.17 TELEPEN 98
- 4.18 UPC-A 99
- 4.18.1 CONVERT TO EAN-13 100
- 4.18.3 CHECKSUM TRANSMISSION 100
- 4.19 UPC-E 101
- 4.19.4 CHECKSUM TRANSMISSION 103
- Enter Setup 104
- 1660 Barcode Scanner 104
- User Guide 104
- Chapter 5 105
- 5.2 CHARACTER SUBSTITUTION 106
- 5.4.2 CHANGE CODE ID 114
- 103 115
- 5.4.3 CLEAR CODE ID SETTINGS 116
- 5.5 LENGTH CODE 117
- 5.6 MULTI-BARCODE EDITOR 120
- Code Type 120
- Chapter 6 123
- 6.1 FORMAT SELECTION 124
- 6.1.2 EXCLUSIVE DATA EDITING 125
- 6.2 EDITING FORMAT 126
- 6.2.2 RESTORE DEFAULT FORMAT 128
- 6.2.3 DEFINE DATA CRITERIA 129
- 119 131
- Start Position 132
- Field Adjustment 132
- Total Number of Fields 132
- 6.2.5 FIELD SETTINGS 134
- 123 135
- Field 2 Setting 135
- Field 3 Setting 136
- 125 137
- Field 4 Setting 137
- Field 5 Setting 138
- 129 141
- 6.3 PROGRAMMING EXAMPLES 142
- 6.3.1 EXAMPLE I 142
- 131 143
- End Programming Format 144
- SPECIFICATIONS 145
- Programming Support 146
- Appendix I 147
- Data bit — 8 148
- Parity — None 148
- Flow control — None 148
- Appendix II 149
- Appendix III 151
- KEY STATUS 152
- USER-DEFINED SCAN CODE 152
- Appendix IV 153
- HEXADECIMAL SYSTEM 154
- ASCII TABLE 155
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce