CipherLab 1660 Specifikace Strana 17
- Strana / 156
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
5
Quick Start
DEFAULT SETTINGS
SAVE USER SETTINGS AS DEFAULTS
For the scanner to keep the customized settings as user defaults, you must have it read
the “Save as User Defaults” label. This is a normal label, and the scanner will respond
with two beeps (low-high tone).
After reading the “Update” label, the current settings will be saved as user defaults.
RESTORE USER DEFAULTS
For the scanner to restore the user defaults, which you have saved earlier, you must
have it read the “Restore User Defaults” label. This is a normal label, and the scanner will
respond with two beeps (low-high tone).
After reading the “Update” label, all the parameters of the scanner will return to their
customized values.
RESTORE SYSTEM DEFAULTS
For the scanner to restore the factory defaults, you must have it read the “Restore
System Defaults” label. This is a normal label, and the scanner will respond with two
beeps (low-high tone).
After reading the “Update” label, all the parameters of the scanner will return to their
default values.
Note: The system default value (if there is) for each setting is indicated by an asterisk
“*”.
Save as User Default
s
Restore User Defaults
Restore System Defaults
- IMPORTANT NOTICES 3
- RELEASE NOTES 5
- CONTENTS 7
- INTRODUCTION 13
- QUICK START 15
- ENTER CONFIGURATION MODE 16
- EXIT CONFIGURATION MODE 16
- Refer to Appendix III 20
- LIST THE CURRENT SETTINGS 21
- Chapter 1 23
- 1.1.3 AUTO POWER OFF 24
- 1.2 MEMORY 26
- 1.2.1 TRANSMIT BUFFER 26
- 1.2.2 MEMORY MODE 26
- Memory Data Delay 27
- Send Data 28
- Clear Data & Confirm 28
- 1.3.1 GOOD READ LED 30
- Beeping 31
- Meaning 31
- 1.4.1 BEEPER VOLUME 32
- 1.4.2 GOOD READ BEEP 33
- 1.4.3 LOW BATTERY ALARM 34
- 1.5 SEND “NR” TO HOST 35
- 1.6 SCAN MODES 36
- 1.6.1 CONTINUOUS MODE 37
- 1.6.5 AUTO POWER OFF MODE 39
- 1.6.6 AIMING MODE 39
- 1.8 DELAY BETWEEN RE-READ 41
- Continuous mode 41
- Auto Power Off mode 41
- 1.9 EFFECTIVE DECODING AREA 42
- 1.9.1 POSITIONING WINDOW 42
- 1.9.2 ADJUSTING WINDOW 42
- Percentage for Right Half 43
- 1.10 NEGATIVE BARCODES 44
- 1.11 SYMBOLOGIES SUPPORTED 44
- Chapter 2 47
- 2.1 BLUETOOTH HID 48
- 2.1.2 RESET CONNECTION 49
- Cap Lock Type Description 51
- Alphabets Transmission 52
- 2.1.4 INTER-FUNCTION DELAY 54
- 2.2 BLUETOOTH SPP 55
- 2.2.1 ACTIVATE BLUETOOTH SPP 55
- 2.2.2 INTER-FUNCTION DELAY 55
- 2.2.3 ACK/NAK TIMEOUT 56
- Chapter 3 57
- 3.1.3 AUTHENTICATION 59
- Chapter 4 67
- 4.1 CODABAR 68
- 4.1.3 CLSI CONVERSION 69
- 4.2 CODE 25 – INDUSTRIAL 25 70
- 4.2.2 CHECKSUM VERIFICATION 71
- 4.2.3 CHECKSUM TRANSMISSION 71
- 4.3 CODE 25 – INTERLEAVED 25 73
- 4.3.2 CHECKSUM VERIFICATION 74
- 4.3.3 CHECKSUM TRANSMISSION 74
- 4.4 CODE 25 – MATRIX 25 76
- 4.4.2 CHECKSUM VERIFICATION 77
- 4.4.3 CHECKSUM TRANSMISSION 77
- 4.5 CODE 39 79
- 4.5.2 CHECKSUM VERIFICATION 79
- 4.5.3 CHECKSUM TRANSMISSION 80
- 4.6 CODE 93 81
- 4.7 CODE 128 81
- 4.8 EAN-8 82
- 4.8.1 CONVERT TO EAN-13 83
- 4.8.2 CHECKSUM TRANSMISSION 83
- 4.9 EAN-13 84
- 4.9.1 ISBN CONVERSION 85
- 4.9.2 ISSN CONVERSION 85
- 4.9.3 CHECKSUM TRANSMISSION 85
- 4.10 EAN-128 86
- 4.10.1 CODE ID TRANSMISSION 86
- 4.11 ISBT 128 87
- 4.12 MSI 88
- 4.12.1 CHECKSUM VERIFICATION 88
- 4.12.2 CHECKSUM TRANSMISSION 89
- 4.13 FRENCH PHARMACODE 91
- 4.13.1 CHECKSUM TRANSMISSION 91
- 4.14 ITALIAN PHARMACODE 92
- 4.14.1 CHECKSUM TRANSMISSION 92
- 4.15 PLESSEY 93
- 4.15.1 CONVERT TO UK PLESSEY 93
- 4.15.2 CHECKSUM TRANSMISSION 93
- 4.16 RSS FAMILY 94
- 4.16.1 CODE ID SELECTION 94
- 4.16.2 RSS-14 94
- 4.16.3 RSS EXPANDED 95
- 4.16.4 RSS LIMITED 96
- Application ID Transmission 97
- Checksum Transmission 97
- 4.17 TELEPEN 98
- 4.18 UPC-A 99
- 4.18.1 CONVERT TO EAN-13 100
- 4.18.3 CHECKSUM TRANSMISSION 100
- 4.19 UPC-E 101
- 4.19.4 CHECKSUM TRANSMISSION 103
- Enter Setup 104
- 1660 Barcode Scanner 104
- User Guide 104
- Chapter 5 105
- 5.2 CHARACTER SUBSTITUTION 106
- 5.4.2 CHANGE CODE ID 114
- 103 115
- 5.4.3 CLEAR CODE ID SETTINGS 116
- 5.5 LENGTH CODE 117
- 5.6 MULTI-BARCODE EDITOR 120
- Code Type 120
- Chapter 6 123
- 6.1 FORMAT SELECTION 124
- 6.1.2 EXCLUSIVE DATA EDITING 125
- 6.2 EDITING FORMAT 126
- 6.2.2 RESTORE DEFAULT FORMAT 128
- 6.2.3 DEFINE DATA CRITERIA 129
- 119 131
- Start Position 132
- Field Adjustment 132
- Total Number of Fields 132
- 6.2.5 FIELD SETTINGS 134
- 123 135
- Field 2 Setting 135
- Field 3 Setting 136
- 125 137
- Field 4 Setting 137
- Field 5 Setting 138
- 129 141
- 6.3 PROGRAMMING EXAMPLES 142
- 6.3.1 EXAMPLE I 142
- 131 143
- End Programming Format 144
- SPECIFICATIONS 145
- Programming Support 146
- Appendix I 147
- Data bit — 8 148
- Parity — None 148
- Flow control — None 148
- Appendix II 149
- Appendix III 151
- KEY STATUS 152
- USER-DEFINED SCAN CODE 152
- Appendix IV 153
- HEXADECIMAL SYSTEM 154
- ASCII TABLE 155
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce