CipherLab 1704 Specifikace Strana 50
- Strana / 226
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
38
Enter Setup
1704 Barcode Scanner
User Guide
Image Capture Autoexposure
Decide whether to manually specify the gain and exposure time (only recommended for advanced
users with difficult image capture situations).
*Enable
Disable
By default, exposure value is set to 10 ms and gain value is set to 50 when autoexposure is
disabled.
Fi
x
ed Exposure
in 100 μ
s
2~5000 (*100)
1. Read the barcode above to specify a fixed exposure value.
2. Read the “
Decimal Value” barcode on page 211. For example, read “1” and “5” for setting the
exposure value to 1.5 ms.
3. Read the “Validate” barcode on the same page to complete this setting
F
ixed Gain
1~100 (*50)
4. Read the barcode above to specify a fixed gain value.
5. Read the “Decimal Value” barcode on page 211. For example, read “3” and “0” for setting the
gain value to 30.
6. Read the “Validate” barcode on the same page to complete this setting.
Gain/Exposure Priority for Image Mode
Alter the decoder’s gain/exposure priority when it acquires an image in Image Mode with auto
exposure enabled.
Low Gain Priority: The decoder favors longer exposure time rather than higher gain to capture
an image. This ensures that the image is less noisy and produces fewer artifacts during
post-processing activities like image enhancement (sharpening). This mode is ideal for fixed
mount/fixed object image capture since the image acquired is susceptible to motion blur.
Low Exposure Priority: The decoder favors higher gain over exposure to capture an image. This
results in an image that is less susceptible to motion blur at the expense of noise artifacts.
However, for most applications, the amount of noise is acceptable.
Low Gain Priority
- 1704 Barcode Scanne 1
- IMPORTANT NOTICES 3
- RELEASE NOTES 5
- CONTENTS 7
- INTRODUCTION 13
- SYMBOLOGIES SUPPORTED 15
- QUICK START 17
- ENTER CONFIGURATION MODE 18
- EXIT CONFIGURATION MODE 18
- Quick Start 19
- Refer to Appendix III 23
- LIST THE CURRENT SETTINGS 24
- Chapter 1 27
- 1.2.2 GOOD READ LED DURATION 29
- 1.3.2 GOOD READ BEEP 31
- 1.4 VIBRATOR 32
- 1.4.1 GOOD READ VIBRATOR 32
- 1.5 SEND “NR” TO HOST 33
- 1.6 SCAN MODES 34
- Chapter 1 35
- 1.6.6 ALTERNATE MODE 37
- 1.6.7 AIMING MODE 37
- 1.6.8 MULTI-BARCODE MODE 38
- 1.8 DELAY BETWEEN RE-READ 40
- Continuous mode 40
- Auto Power Off mode 40
- Alternate mode 40
- 1.9 READ REDUNDANCY (1D) 41
- 1.13 OPERATION MODE 44
- 1.13.2 ENTER/EXIT IMAGE MODE 47
- 1.13.3 IMAGE MODE SETTINGS 48
- 1.13.4 ENTER/EXIT VIDEO MODE 52
- 1.13.5 VIDEO MODE SETTINGS 52
- 1.14 IMAGER PREFERENCES 53
- 1.14.1 IMAGE ENHANCEMENT 53
- 1.14.2 IMAGE RESOLUTION 54
- 1.14.3 IMAGE CROPPING 55
- 1.14.4 IMAGE FILE FORMAT 56
- 1.14.5 BITS PER PIXEL 56
- 1.14.6 JPEG IMAGE OPTIONS 57
- 1.15 SIGNATURE CAPTURE 58
- 1.16 CABLE AUTO-DETECT 61
- Chapter 2 63
- IN THIS CHAPTER 64
- 2.1 KEYBOARD WEDGE 65
- Chapter 2 67
- Selecting Output Interface 67
- 2.1.3 INTER-CHARACTER DELAY 75
- 2.1.4 INTER-FUNCTION DELAY 75
- 2.2 RS-232 76
- 2.2.2 BAUD RATE 76
- 2.2.3 DATA BITS 77
- 2.2.4 PARITY 77
- 2.2.5 STOP BIT 77
- 2.2.6 FLOW CONTROL 78
- 2.2.7 INTER-CHARACTER DELAY 79
- 2.2.8 INTER-FUNCTION DELAY 79
- 2.2.9 ACK/NAK TIMEOUT 80
- 2.3 DIRECT USB HID 81
- 2.3.3 INTER-FUNCTION DELAY 89
- 2.4 DIRECT USB VIRTUAL COM 90
- 2.4.2 INTER-FUNCTION DELAY 90
- 2.4.3 ACK/NAK TIMEOUT 91
- Chapter 3 93
- 3.1 CODABAR 94
- 3.1.2 CLSI CONVERSION 94
- 3.2 CODE 25 – INDUSTRIAL 25 96
- 3.3 CODE 25 – INTERLEAVED 25 98
- 3.3.1 VERIFY CHECK DIGIT 98
- 3.3.2 TRANSMIT CHECK DIGIT 98
- 3.3.3 CONVERT TO EAN-13 99
- 1704 Barcode Scanner 100
- User Guide 100
- 3.4 CODE 25 – MATRIX 25 101
- 3.4.1 VERIFY CHECK DIGIT 101
- 3.4.2 TRANSMIT CHECK DIGIT 101
- 3.5 CODE 25 – CHINESE 25 103
- 3.7.2 TRANSMIT CHECK DIGIT 105
- 3.7 CODE 39 105
- 3.7.1 VERIFY CHECK DIGIT 105
- Chapter 3 107
- Changing Symbology Settings 107
- 3.8 TRIOPTIC CODE 39 108
- 3.9 CODE 93 109
- 3.10 CODE 128 111
- 3.11 GS1-128 (EAN-128) 112
- 3.11.1 TRANSMIT CODE ID 112
- GS1 DataBar Expanded 117
- 3.13.5 CONVERT TO UPC/EAN 119
- 3.14 MSI 120
- 3.14.1 VERIFY CHECK DIGIT 120
- 3.14.2 TRANSMIT CHECK DIGIT 120
- 3.15 EAN-8 122
- 3.16 EAN-13 123
- 3.16.1 CONVERT TO ISBN 124
- 3.16.2 CONVERT TO ISSN 124
- 3.18 UPC-A 126
- 3.18.2 TRANSMIT CHECK DIGIT 127
- 3.19 UPC-E 128
- 3.19.4 TRANSMIT CHECK DIGIT 130
- 3.20 CODE 11 131
- 3.20.1 VERIFY CHECK DIGIT 131
- 3.20.2 TRANSMIT CHECK DIGIT 131
- 3.21 COMPOSITE CODE 133
- 3.21.1 COMPOSITE CC-A/B 133
- 3.21.2 COMPOSITE CC-C 133
- 3.21.3 COMPOSITE TLC-39 133
- 3.22 US POSTAL CODE 135
- 3.22.1 US POSTNET 135
- 3.22.2 US PLANET 135
- 3.22.3 TRANSMIT CHECK DIGIT 135
- 3.23 UK POSTAL CODE 136
- 3.23.1 UK POSTAL 136
- 3.23.2 TRANSMIT CHECK DIGIT 136
- 3.24.5 UPU FICS POSTAL 138
- 3.25 2D SYMBOLOGIES 139
- 3.25.1 PDF417 139
- 3.25.2 MicroPDF417 139
- 3.25.3 DATA MATRIX 140
- 3.25.4 MAXICODE 141
- 3.25.5 QR CODE 141
- 3.25.6 MicroQR 141
- 3.25.7 AZTEC 141
- Chapter 4 145
- Chapter 4 147
- Defining Output Format 147
- 4.4.2 CHANGE CODE ID 162
- 4.4.3 CLEAR CODE ID SETTINGS 165
- 4.5 LENGTH CODE 166
- 4.6 MULTI-BARCODE EDITOR 174
- Code Type 174
- Chapter 5 179
- 5.1.2 EXCLUSIVE DATA EDITING 181
- 5.2.2 RESTORE DEFAULT FORMAT 184
- 5.3.1 APPLICABLE CODE TYPE 185
- 5.3.2 DATA LENGTH 195
- Specify a value 195
- 5.4.3 TOTAL NUMBER OF FIELDS 198
- 5.4.4 FIELD SETTINGS 199
- 189 201
- Field 3 Setting 201
- 191 203
- Field 5 Setting 203
- 5.4.5 PAUSE FIELD SETTING 205
- 195 207
- 5.6 PROGRAMMING EXAMPLES 208
- 5.6.1 EXAMPLE I 208
- 197 209
- SPECIFICATIONS 211
- Appendix I 213
- Click [OK] 214
- Appendix I Firmware Up 215
- Appendix II 217
- Appendix III 219
- KEY TYPE & STATUS 220
- KEY TYPE 220
- KEY STATUS 220
- EXAMPLE 221
- Appendix IV 223
- HEXADECIMAL SYSTEM 224
- ASCII TABLE 225
Související produkty a manuály pro Čtečky čárových kódů CipherLab 1704
Čtečky čárových kódů CipherLab 1502 Uživatelská příručka
(150 stránky)
(150 stránky)
Čtečky čárových kódů CipherLab 1504 Uživatelská příručka
(217 stránky)
(217 stránky)
Čtečky čárových kódů CipherLab 1661 Specifikace
(235 stránky)
(235 stránky)
Čtečky čárových kódů CipherLab 1564 Specifikace
(267 stránky)
(267 stránky)
Čtečky čárových kódů CipherLab 1502 Specifikace
(174 stránky)
(174 stránky)
Čtečky čárových kódů CipherLab 1266 Specifikace
(180 stránky)
(180 stránky)
Čtečky čárových kódů CipherLab 1562 Uživatelská příručka
(160 stránky)
(160 stránky)
Čtečky čárových kódů CipherLab 1564 Uživatelský manuál
(277 stránky)
(277 stránky)
Alto Mixer audio manuali utente
Partendo da A
| Modelli | Tipo di Documento |
|---|---|
| AMX-180FX | |
| AMX-80 | |
| APM10 | |
| APM160 | |
| APM80.1000 |
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce