CipherLab 1661 Specifikace Strana 160
- Strana / 235
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
146
Enter Setup
1660 Barcode Scanner
User Guide
5.2 CHARACTER SUBSTITUTION
Character substitution is performed on every occurrence of the first character specified. If
only one character is specified, every occurrence of that character in the barcode will be
taken away.
The first character will be replaced by the second character(s).
Up to three sets of character substitution can be configured.
If “BT HID” or “USB HID” is configured for interface, Key Type and Key Status will
then become applicable. You may decide whether or not to apply Key Status when
“Normal Key” is selected for Key Type.
Key Type Key Status
Scan Code Only 1 scan code value is allowed.
Refer to 5.2.1 Select a Set for
Character Substitution
.
N/A
Normal Key Up to 3 character strings are
allowed.
Add Shift
Add Left Ctrl
Add Left Alt
Add Right Ctrl
Add Right Alt
Refer to
Keyboard Wedge Table.
Note: The character substitution is performed only on the barcode itself and before the
processing of editing formats. It is not applicable to the Prefix/Suffix Code, Code
ID, Length Code, or any Additional Field.
- 1660/1661 Barcode Scanne 1
- IMPORTANT NOTICES 3
- RELEASE NOTES 5
- CONTENTS 9
- INTRODUCTION 15
- Introduction 17
- USING 3610 19
- SYMBOLOGIES SUPPORTED 21
- QUICK START 23
- ENTER CONFIGURATION MODE 25
- EXIT CONFIGURATION MODE 25
- Quick Start 27
- Refer to Appendix III 30
- LIST THE CURRENT SETTINGS 31
- Chapter 1 35
- Chapter 1 37
- 1.2 MEMORY 40
- 1.2.1 TRANSMIT BUFFER 40
- 1.2.2 MEMORY MODE 41
- 1.3.1 GOOD READ LED 44
- 1.3.2 GOOD READ LED DURATION 44
- 1.4.1 BEEPER VOLUME 46
- 1.4.2 GOOD READ BEEP 47
- 1.5 SEND “NR” TO HOST 49
- 1.6 SCAN MODES 50
- 1.6.6 ALTERNATE MODE 53
- 1.6.7 AIMING MODE 53
- 1.6.8 MULTI-BARCODE MODE 54
- 1.8 DELAY BETWEEN RE-READ 56
- Continuous mode 56
- Auto Power Off mode 56
- Alternate mode 56
- 1.11 NEGATIVE BARCODES 59
- 1.12 EFFECTIVE DECODING AREA 60
- 1.12.1 POSITIONING WINDOW 60
- 1.12.2 ADJUSTING WINDOW 61
- 1.14 HARDWARE RESET 63
- 1.14.2 RESET CONNECTION 63
- Chapter 2 65
- 2.1 BT HID 66
- 2.1.2 RESET CONNECTION 67
- 2.1.4 INTER-FUNCTION DELAY 75
- 2.2 BT SPP SLAVE 77
- 2.2.2 INTER-FUNCTION DELAY 77
- 2.2.3 ACK/NAK TIMEOUT 78
- 2.3 BT SPP MASTER 79
- “Set Connection” 79
- “MAC ID” 79
- 2.3.2 INTER-FUNCTION DELAY 81
- 2.3.3 ACK/NAK TIMEOUT 82
- 2.4 USB HID VIA 3610 83
- 2.4.3 INTER-FUNCTION DELAY 91
- 2.5 USB VIRTUAL COM VIA 3610 92
- 2.5.2 INTER-FUNCTION DELAY 92
- 2.5.3 ACK/NAK TIMEOUT 93
- 1660 Barcode Scanner 100
- User Guide 100
- Chapter 2 101
- Selecting Output Interface 101
- 2.6.3 INTER-FUNCTION DELAY 102
- 2.7.2 INTER-FUNCTION DELAY 103
- 2.7.3 ACK/NAK TIMEOUT 104
- Chapter 3 105
- 3.1 CONNECTING VIA 3610 106
- 3.1.1 CONNECT TO 3610 106
- “Set Connection” label 106
- “Serial Number” label 106
- 3.1.2 CHANGE INTERFACE 107
- 3.2 CONNECTING VIA BLUETOOTH 109
- DONGLE 109
- 3.2.1 CHANGE INTERFACE 109
- Chapter 3 111
- 3.2.3 CONNECT TO DONGLE 113
- Chapter 4 121
- 4.1 CODABAR 122
- 4.1.3 CLSI CONVERSION 123
- 4.2 CODE 25 – INDUSTRIAL 25 124
- 4.2.2 VERIFY CHECK DIGIT 125
- 4.2.3 TRANSMIT CHECK DIGIT 125
- 4.3 CODE 25 – INTERLEAVED 25 127
- 4.3.2 VERIFY CHECK DIGIT 128
- 4.3.3 TRANSMIT CHECK DIGIT 128
- Chapter 4 129
- Changing Symbology Settings 129
- 4.4 CODE 25 – MATRIX 25 130
- 4.4.2 VERIFY CHECK DIGIT 131
- 4.4.3 TRANSMIT CHECK DIGIT 131
- 4.5 CODE 39 133
- 4.5.2 VERIFY CHECK DIGIT 133
- 4.5.3 TRANSMIT CHECK DIGIT 134
- 4.6 CODE 93 135
- 4.7 CODE 128 135
- 4.8 EAN-8 136
- 4.8.1 CONVERT TO EAN-13 137
- 4.8.2 TRANSMIT CHECK DIGIT 137
- 4.9 EAN-13 138
- 4.9.1 ISBN CONVERSION 139
- 4.9.2 ISSN CONVERSION 139
- 4.9.3 TRANSMIT CHECK DIGIT 139
- 4.9.4 SECURITY LEVEL 140
- 4.10 GS1-128 (EAN-128) 141
- 4.10.1 CODE ID TRANSMISSION 141
- 4.11 ISBT 128 142
- 4.12 MSI 143
- 4.12.1 VERIFY CHECK DIGIT 143
- 4.12.2 TRANSMIT CHECK DIGIT 143
- 4.13 FRENCH PHARMACODE 145
- 4.13.1 TRANSMIT CHECK DIGIT 145
- 4.14 ITALIAN PHARMACODE 146
- 4.14.1 TRANSMIT CHECK DIGIT 146
- 4.15 PLESSEY 147
- 4.15.1 CONVERT TO UK PLESSEY 147
- 4.15.2 TRANSMIT CHECK DIGIT 147
- GS1 DataBar Expanded 151
- 4.17 TELEPEN 153
- 4.18 UPC-A 154
- 4.18.1 CONVERT TO EAN-13 155
- 4.18.3 TRANSMIT CHECK DIGIT 155
- 4.19 UPC-E 156
- 4.19.4 TRANSMIT CHECK DIGIT 158
- Chapter 5 159
- Chapter 5 161
- Defining Output Format 161
- 5.4.2 CHANGE CODE ID 171
- 5.4.3 CLEAR CODE ID SETTINGS 172
- 5.5 LENGTH CODE 173
- 5.6 MULTI-BARCODE EDITOR 177
- Code Type 177
- Chapter 6 181
- 6.1.2 EXCLUSIVE DATA EDITING 183
- 6.2 EDITING FORMAT 184
- 6.2.2 RESTORE DEFAULT FORMAT 186
- 6.3.1 APPLICABLE CODE TYPE 187
- 179 193
- 6.3.2 DATA LENGTH 194
- 6.4.3 TOTAL NUMBER OF FIELDS 197
- 6.4.4 FIELD SETTINGS 198
- 187 201
- Field 4 Setting 201
- 189 203
- Additional Fields 203
- Key Type Key Status 203
- 6.4.5 PAUSE FIELD SETTING 204
- 6.6 PROGRAMMING EXAMPLES 207
- 6.6.1 EXAMPLE I 207
- SPECIFICATIONS 209
- Appendix I 211
- Click [OK] 212
- Appendix I Firmware Upgrade 213
- USING BLUETOOTH 215
- Appendix II 221
- Appendix II 223
- Host Serial Commands 223
- 3610 SERIAL COMMAND TABLE 224
- EXAMPLE 226
- Appendix III 227
- KEY TYPE & STATUS 228
- KEY TYPE 228
- KEY STATUS 228
- Appendix IV 231
- HEXADECIMAL SYSTEM 232
- ASCII TABLE 233
- USE PRESET PIN 234
Související produkty a manuály pro Čtečky čárových kódů CipherLab 1661
Čtečky čárových kódů CipherLab 1564 Specifikace
(267 stránky)
(267 stránky)
Čtečky čárových kódů CipherLab 1502 Specifikace
(174 stránky)
(174 stránky)
Čtečky čárových kódů CipherLab 1266 Specifikace
(180 stránky)
(180 stránky)
Čtečky čárových kódů CipherLab 1562 Uživatelská příručka
(160 stránky)
(160 stránky)
Čtečky čárových kódů CipherLab 1564 Uživatelský manuál
(277 stránky)
(277 stránky)
Čtečky čárových kódů CipherLab 1660 Specifikace
(156 stránky)
(156 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce