CipherLab 1502 Uživatelská příručka stáhnout pdf (Strana 118)

108

End Programming Format

1500/1502 Barcode Scanner User Guide

5.1 FORMAT SELECTION

5.1.1 ACTIVATE EDITING FORMATS

If you have already configured any editing format before, you may directly apply the

editing format. If not, you must start with configuring an editing format first, and then,

activate the editing format when it is desired in use.

Editing Format 1

Editing Format 2

Editing Format 3

*Disable Format 1

Enable Format 1

Disable Format 2

Enable Format 2

Disable Format 3

Enable Format 3

1 2 ... 113 114 115 116 117 118 119 120 121 122 123 ... 149 150

1500/1502 Barcode Scanne 1
IMPORTANT NOTICES 3
RELEASE NOTES 5
CONTENTS 7
INTRODUCTION 11
Enter Setup 12
QUICK START 13
ENTER CONFIGURATION MODE 14
EXIT CONFIGURATION MODE 14
 Refer to Appendix III 19
LIST THE CURRENT SETTINGS 20
Chapter 1 23
Beeping 26
Meaning 26
1.4.2 GOOD READ BEEP 27
1.5 SEND “NR” TO HOST 28
1.6 SCAN MODES 29
1.6.1 CONTINUOUS MODE 30
1.6.5 AUTO POWER OFF MODE 32
1.6.6 AIMING MODE 32
1.6.7 MULTI-BARCODE MODE 33
1.6.8 ALTERNATE MODE 33
1.8 DELAY BETWEEN RE-READ 35
 Continuous mode 35
 Auto Power Off mode 35
 Alternate mode 35
1.9 EFFECTIVE DECODING AREA 36
1.9.1 POSITIONING WINDOW 36
1.9.2 ADJUSTING WINDOW 36
Percentage for Right Half 37
1.11 NEGATIVE BARCODES 39
1.12 SYMBOLOGIES SUPPORTED 39
Chapter 2 43
2.1 KEYBOARD WEDGE 44
2.1.2 KEYBOARD SETTINGS 45
Alphabets Transmission 49
Digits Transmission 49
ALT Composing 50
Laptop Support 50
2.1.3 INTER-CHARACTER DELAY 51
2.1.4 INTER-FUNCTION DELAY 51
2.2 RS-232 52
2.2.2 BAUD RATE 52
2.2.3 DATA BITS 53
2.2.4 PARITY 53
2.2.5 STOP BIT 54
2.2.6 FLOW CONTROL 54
2.2.7 INTER-CHARACTER DELAY 55
2.2.8 INTER-FUNCTION DELAY 55
2.2.9 ACK/NAK TIMEOUT 56
2.3 WAND EMULATION 57
2.3.2 NORMAL STATE 57
2.3.3 BAR STATE 57
2.3.4 MODULE TIME 58
2.3.5 MARGIN TIME 59
Chapter 3 61
3.1 CODABAR 62
3.1.3 CLSI CONVERSION 63
3.2 CODE 25 – INDUSTRIAL 25 64
3.2.2 CHECKSUM VERIFICATION 65
3.2.3 CHECKSUM TRANSMISSION 65
3.3 CODE 25 – INTERLEAVED 25 67
3.3.2 CHECKSUM VERIFICATION 68
3.3.3 CHECKSUM TRANSMISSION 68
3.4 CODE 25 – MATRIX 25 70
3.4.2 CHECKSUM VERIFICATION 71
3.4.3 CHECKSUM TRANSMISSION 71
3.5 CODE 39 73
3.5.2 CHECKSUM VERIFICATION 73
3.5.3 CHECKSUM TRANSMISSION 74
3.6 CODE 93 75
3.7 CODE 128 75
3.8 EAN-8 76
3.8.1 CONVERT TO EAN-13 77
3.8.2 CHECKSUM TRANSMISSION 77
3.9 EAN-13 78
3.9.1 ISBN CONVERSION 79
3.9.2 ISSN CONVERSION 79
3.9.3 CHECKSUM TRANSMISSION 79
3.10 EAN-128 80
3.10.1 CODE ID TRANSMISSION 80
3.11 ISBT 128 81
3.12 MSI 82
3.12.1 CHECKSUM VERIFICATION 82
3.12.2 CHECKSUM TRANSMISSION 83
3.13 FRENCH PHARMACODE 85
3.13.1 CHECKSUM TRANSMISSION 85
3.14 ITALIAN PHARMACODE 86
3.14.1 CHECKSUM TRANSMISSION 86
3.15 PLESSEY 87
3.15.1 CONVERT TO UK PLESSEY 87
3.15.2 CHECKSUM TRANSMISSION 87
3.16 RSS FAMILY 88
3.16.1 CODE ID SELECTION 88
3.16.2 RSS-14 88
3.16.3 RSS EXPANDED 89
3.16.4 RSS LIMITED 90
Application ID Transmission 91
Checksum Transmission 91
3.17 TELEPEN 92
3.18 UPC-A 93
3.18.1 CONVERT TO EAN-13 94
3.18.3 CHECKSUM TRANSMISSION 94
3.19 UPC-E 95
3.19.4 CHECKSUM TRANSMISSION 97
Chapter 4 99
4.2 CHARACTER SUBSTITUTION 100
4.4.2 CHANGE CODE ID 108
4.4.3 CLEAR CODE ID SETTINGS 110
4.5 LENGTH CODE 111
4.6 MULTI-BARCODE EDITOR 114
 Code Type 114
Chapter 5 117
5.1 FORMAT SELECTION 118
5.1.2 EXCLUSIVE DATA EDITING 119
5.2 EDITING FORMAT 120
5.2.2 RESTORE DEFAULT FORMAT 122
5.2.3 DEFINE DATA CRITERIA 123
115 125
Start Position 126
Field Adjustment 126
Total Number of Fields 126
5.2.5 FIELD SETTINGS 128
119 129
Field 2 Setting 129
Field 3 Setting 130
121 131
Field 4 Setting 131
Field 5 Setting 132
125 135
5.3 PROGRAMMING EXAMPLES 136
5.3.1 EXAMPLE I 136
127 137
SPECIFICATIONS 139
Programming Support 140
Appendix I 141
Appendix II 143
Remarks 144
Appendix III 145
KEY STATUS 146
USER-DEFINED SCAN CODE 146
Appendix IV 147
HEXADECIMAL SYSTEM 148
ASCII TABLE 149

Komentáře k této Příručce

Žádné komentáře

CipherLab 1502 Uživatelská příručka Strana 118

Komentáře k této Příručce

Související produkty a manuály pro Čtečky čárových kódů CipherLab 1502